Desain Rangkaian Gate-Driver untuk Konverter yang Bekerja dengan Voltage Mode Control

Main Article Content

Fitriadi .
Muh. Imran Hamid
Jurusan Teknik Elektro, Fakultas Teknik, Universitas Andalas

Keywords

Abstract

 Converter DC / AC with full bridge topology developed from a series combination of semiconductor components type IGBT / MOSFET. In this series IGBT / MOSFET functioning as a switch, if it gets the supply PWM control signal at the gate 10-20 Volt DC. To strengthen the PWM control signal is generated microcontroller can use gate-driver circuit. In this paper, a gate-driver circuit developed from the type MC33153 driver IC application and HCPL4506. ± 18 V DC supply for the input generated from the driver IC converters DC / DC isolated system, so the four PWM control signal output from the gate driver circuit is also isolated. The contribution of this study is a gete driver circuit which can be used for a converter that works with methods Phase Shift (PS) with a control technique Voltage Mode Control (VMC) has been successfully realized.

Keywords: Full-bridge, converter, gate-driver


Abstrak- Konverter DC/AC dengan topologi jembatan penuh yang dikembangkan dari rangkaian kombinasi komponen semikonduktor jenis IGBT/MOSFET. Dalam rangkaian ini IGBT/MOSFET berfungsi sebagai switch, jika mendapat suplai sinyal kontrol PWM pada kaki gate 10-20 Volt DC. Untuk menguatkan sinyal kontrol PWM yang dibangkitkan mikrokontroler dapat menggunakan rangkaian gate-driver. Dalam paper ini, sebuah rangkaian gate-driver dikembangkan dari aplikasi IC driver tipe MC33153 dan HCPL4506. Suplai DC ± 18 V untuk input IC driver dihasilkan dari konverter DC/DC yang terisolasi secara sistem, sehingga keempat sinyal kontrol PWM output dari rangkaian gate driver juga terisolasi. Kontribusi dari penelitian ini adalah sebuah rangkaian gete driver yang dapat digunakan untuk konverter yang bekerja dengan metode Phase Shift (PS) dengan teknik kontrol Voltage Mode Control (VMC) telah berhasil direalisasikan.

Kata kunci : Full-bridge, converter, gate-driver

References

[1] Irawan. J. A., Firmansyah. E., Wijaya. F. D.; Perancangan Transformator Frekuensi Tinggi untuk Konverter DC-DC Full-Bridge Phase-Shifted 200 W. Seminar Nasional Aplikasi Teknologi Informasi (SNATI) 2013 Yogyakarta, 15 Juni 2013.

[2] Zheng. W., Meiying. Q.; The Application of IGBT Driver MC33153. IEEE. 978-1-4244- 7618-3. 2010

[3] Tarmizi, Muyassar.; Rancang Bangun Inverter SVM Berbasis Mikrokontroler PIC 18F4431untuk Sistem VSD. Jurnal Nasional Teknik Elektro. Vol: 2 No. 1 Maret 2013.

[4] Avago Technologies.; Data sheet HCPL 4506. www.avagotech.com

[5] Vishay Siliconix.; Data sheet Power MOSFET IRF 530.

[6] Puyal. D., Barragán. L. A., Acero. J.; An FPGA-Based Digital Modulator for Full- or Half-Bridge Inverter Control. IEEE Transactions On Power Electronics, Vol. 21, No. 5, September 2006.

[7] Arya. P. S., Chithra. R.; Phase Shifted Full Bridge DC-DC Converter. International Research Journal of Engineering and Technology (IRJET). Volume: 02 Issue: 04. July-2015.

[8] Texas Instruments.; Phase-Shifted Full Bridge DC/DC Power Converter Design Guide. May 2014. www.ti.com

[9] Nene. H.; Implementing advanced control strategies for phase-shifted, fullbridge DC/Dcconverters using MCUs (Part 1of 2). Systems and Applications, for Texas Instruments Incorporated. 2000

Article Sidebar

PDF
Published
Apr 28, 2016
DOI https://doi.org/10.25077/jnte.v5n2.259.2016

Article Details

How to Cite
., F., & Hamid, M. I. (2016). Desain Rangkaian Gate-Driver untuk Konverter yang Bekerja dengan Voltage Mode Control. Jurnal Nasional Teknik Elektro, 5(2), 175–180. https://doi.org/10.25077/jnte.v5n2.259.2016
Issue
Vol. 5 No. 2: Juli 2016
Section
Electrical Power and Energy

Authors who publish with this journal agree to the following terms:

    1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
    2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
    3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

The authors declare that:

1.        This paper has not been published in the same form elsewhere.

2.        It will not be submitted anywhere else for publication prior to acceptance/rejection by this Journal.

3.        A copyright permission is obtained for materials published elsewhere and which require this permission for reproduction.